diff options
Diffstat (limited to 'third_party/TouchSense/STMTouch_Driver/inc/tsl_conf_stm32f3xx.h_TOADAPT')
| -rw-r--r-- | third_party/TouchSense/STMTouch_Driver/inc/tsl_conf_stm32f3xx.h_TOADAPT | 628 |
1 files changed, 628 insertions, 0 deletions
diff --git a/third_party/TouchSense/STMTouch_Driver/inc/tsl_conf_stm32f3xx.h_TOADAPT b/third_party/TouchSense/STMTouch_Driver/inc/tsl_conf_stm32f3xx.h_TOADAPT new file mode 100644 index 0000000..547555e --- /dev/null +++ b/third_party/TouchSense/STMTouch_Driver/inc/tsl_conf_stm32f3xx.h_TOADAPT @@ -0,0 +1,628 @@ +/** + ****************************************************************************** + * @file tsl_conf_stm32f3xx.h + * @author MCD Application Team + * @version V1.4.4 + * @date 31-March-2014 + * @brief Acquisition parameters for STM32F3xx products. + * @note This file must be copied in the application project and values + * changed for the application. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __TSL_CONF_STM32F3XX_H +#define __TSL_CONF_STM32F3XX_H + +//++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +//+++++++++++++++++++++++++++ COMMON PARAMETERS ++++++++++++++++++++++++++++++++ +//++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ + +/** @defgroup Common_Parameters Common Parameters + * @{ */ + +//============================================================================== +// Number of elements +//============================================================================== + +/** @defgroup Common_Parameters_Number_Of_Elements 01 - Number of elements + * @{ */ + +/** Total number of channels in application (range=1..255) +*/ +#define TSLPRM_TOTAL_CHANNELS (1) + +/** Total number of banks in application (range=1..255) +*/ +#define TSLPRM_TOTAL_BANKS (1) + +/** Total number of "Extended" TouchKeys in application (range=0..255) +*/ +#define TSLPRM_TOTAL_TOUCHKEYS (1) + +/** Total number of "Basic" TouchKeys in application (range=0..255) +*/ +#define TSLPRM_TOTAL_TOUCHKEYS_B (1) + +/** Total number of "Extended" Linear and Rotary sensors in application (range=0..255) + - Count also the 1-channel linear sensor used as TouchKey +*/ +#define TSLPRM_TOTAL_LINROTS (1) + +/** Total number of "Basic" Linear and Rotary sensors in application (range=0..255) + - Count also the 1-channel linear sensor used as TouchKey +*/ +#define TSLPRM_TOTAL_LINROTS_B (1) + +/** Total number of sensors/objects in application (range=1..255) + - Count all TouchKeys, Linear and Rotary sensors +*/ +#define TSLPRM_TOTAL_OBJECTS (1) + +/** @} Common_Parameters_Number_Of_Elements */ + +//============================================================================== +// Optional features +//============================================================================== + +/** @defgroup Common_Parameters_Options 02 - Optional features + * @{ */ + +/** Record the last measure (0=No, 1=Yes) + - If No the measure is recalculated using the Reference and Delta +*/ +#define TSLPRM_USE_MEAS (1) + +/** Zone management usage (0=No, 1=Yes) +*/ +#define TSLPRM_USE_ZONE (1) + +/** Proximity detection usage (0=No, 1=Yes) +*/ +#define TSLPRM_USE_PROX (1) + +/** Use the Timer tick callback (0=No, 1=Yes) + - When equal to 1, the function TSL_CallBack_TimerTick must be defined in + the application code. It is called for each timer interruption. +*/ +#define TSLPRM_USE_TIMER_CALLBACK (1) + +/** Acquisition interrupt mode (0=No, 1=Yes) + - If No the TS interrupt is not used. + - If Yes the TS interrupt is used. +*/ +#define TSLPRM_USE_ACQ_INTERRUPT (1) + +/** @} Common_Parameters_Options */ + +//============================================================================== +// Acquisition limits +//============================================================================== + +/** @defgroup Common_Parameters_Acquisition_Limits 03 - Acquisition limits + * @{ */ + +/** Minimum acquisition measurement (range=0..65535) + - This is the minimum acceptable value for the acquisition measure. + - The acquisition will be in error if the measure is below this value. +*/ +#define TSLPRM_ACQ_MIN (10) + +/** Maximum acquisition measurement (range=255, 511, 1023, 2047, 8191, 16383) + - This is the maximum acceptable value for the acquisition measure. + - The acquisition will be in error if the measure is above this value. +*/ +#define TSLPRM_ACQ_MAX (8191) + +/** @} Common_Parameters_Acquisition_Limits */ + +//============================================================================== +// Calibration +//============================================================================== + +/** @defgroup Common_Parameters_Calibration 04 - Calibration + * @{ */ + +/** Number of calibration samples (range=4, 8, 16) + - Low value = faster calibration but less precision. + - High value = slower calibration but more precision. +*/ +#define TSLPRM_CALIB_SAMPLES (8) + +/** Delay in measurement samples before starting the calibration (range=0..40) + - This is useful if a noise filter is used. + - Write 0 to disable the delay. +*/ +#define TSLPRM_CALIB_DELAY (10) + +/** @} Common_Parameters_Calibration */ + +//============================================================================== +// Thresholds for TouchKey sensors +//============================================================================== + +/** @defgroup Common_Parameters_TouchKey_Thresholds 05 - Thresholds for TouchKey sensors + * @{ */ + +/** TouchKeys Proximity state input threshold (range=0..255) + - Enter Proximity state if delta is above +*/ +#define TSLPRM_TKEY_PROX_IN_TH (10) + +/** TouchKeys Proximity state output threshold (range=0..255) + - Exit Proximity state if delta is below +*/ +#define TSLPRM_TKEY_PROX_OUT_TH (5) + +/** TouchKeys Detect state input threshold (range=0..255) + - Enter Detect state if delta is above +*/ +#define TSLPRM_TKEY_DETECT_IN_TH (20) + +/** TouchKeys Detect state output threshold (range=0..255) + - Exit Detect state if delta is below +*/ +#define TSLPRM_TKEY_DETECT_OUT_TH (15) + +/** TouchKeys re-Calibration threshold (range=0..255) + - @warning The value is inverted in the sensor state machine + - Enter Calibration state if delta is below +*/ +#define TSLPRM_TKEY_CALIB_TH (20) + +/** TouchKey, Linear and Rotary sensors thresholds coefficient (range=0..4) + This multiplier coefficient is applied on Detect and Re-Calibration thresholds only. + - 0: feature disabled + - 1: thresholds x 2 + - 2: thresholds x 4 + - 3: thresholds x 8 + - 4: thresholds x 16 +*/ +#define TSLPRM_COEFF_TH (1) + +/** @} Common_Parameters_TouchKey_Thresholds */ + +//============================================================================== +// Thresholds for Linear and Rotary sensors +//============================================================================== + +/** @defgroup Common_Parameters_LinRot_Thresholds 06 - Thresholds for Linear and Rotary sensors + * @{ */ + +/** Linear/Rotary Proximity state input threshold (range=0..255) + - Enter Proximity state if delta is above +*/ +#define TSLPRM_LINROT_PROX_IN_TH (10) + +/** Linear/Rotary Proximity state output threshold (range=0..255) + - Exit Proximity state if delta is below +*/ +#define TSLPRM_LINROT_PROX_OUT_TH (5) + +/** Linear/Rotary Detect state input threshold (range=0..255) + - Enter Detect state if delta is above +*/ +#define TSLPRM_LINROT_DETECT_IN_TH (20) + +/** Linear/Rotary Detect state output threshold (range=0..255) + - Exit Detect state if delta is below +*/ +#define TSLPRM_LINROT_DETECT_OUT_TH (15) + +/** Linear/Rotary re-Calibration threshold (range=0..255) + - @warning The value is inverted in the sensor state machine + - Enter Calibration state if delta is below + - A low absolute value will result in a higher sensitivity and thus some spurious + recalibration may be issued. +*/ +#define TSLPRM_LINROT_CALIB_TH (20) + +/** Linear/Rotary Delta normalization (0=No, 1=Yes) + - When this parameter is set, a coefficient is applied on all Delta of all sensors + in order to normalize them and to improve the position calculation. + - These coefficients must be defined in a constant table in the application (see Library examples). + - The MSB is the coefficient integer part, the LSB is the coefficient real part. + - Examples: + - To apply a factor 1.10: + 0x01 to the MSB + 0x1A to the LSB (0.10 x 256 = 25.6 -> rounded to 26 = 0x1A) + - To apply a factor 0.90: + 0x00 to the MSB + 0xE6 to the LSB (0.90 x 256 = 230.4 -> rounded to 230 = 0xE6) + - To apply no factor: + 0x01 to the MSB + 0x00 to the LSB +*/ +#define TSLPRM_LINROT_USE_NORMDELTA (1) + +/** @} Common_Parameters_LinRot_Thresholds */ + +//============================================================================== +// Linear/Rotary sensors used +//============================================================================== + +/** @defgroup Common_Parameters_LinRot_Used 07 - Linear/Rotary sensors used + * @{ */ + +/** Select which Linear and Rotary sensors you use in your application. + - 0 = Not Used + - 1 = Used + + LIN = Linear sensor + ROT = Rotary sensor + M1 = Mono electrodes design with 0/255 position at extremities of the sensor + M2 = Mono electrodes design + H = Half-ended electrodes design + D = Dual electrodes design +*/ +#define TSLPRM_USE_3CH_LIN_M1 (1) +#define TSLPRM_USE_3CH_LIN_M2 (1) +#define TSLPRM_USE_3CH_LIN_H (1) +#define TSLPRM_USE_3CH_ROT_M (1) + +#define TSLPRM_USE_4CH_LIN_M1 (1) +#define TSLPRM_USE_4CH_LIN_M2 (1) +#define TSLPRM_USE_4CH_LIN_H (1) +#define TSLPRM_USE_4CH_ROT_M (1) + +#define TSLPRM_USE_5CH_LIN_M1 (1) +#define TSLPRM_USE_5CH_LIN_M2 (1) +#define TSLPRM_USE_5CH_LIN_H (1) +#define TSLPRM_USE_5CH_ROT_M (1) +#define TSLPRM_USE_5CH_ROT_D (1) + +#define TSLPRM_USE_6CH_LIN_M1 (1) +#define TSLPRM_USE_6CH_LIN_M2 (1) +#define TSLPRM_USE_6CH_LIN_H (1) +#define TSLPRM_USE_6CH_ROT_M (1) + +/** @} Common_Parameters_LinRot_used */ + +//============================================================================== +// Linear/Rotary sensors position +//============================================================================== + +/** @defgroup Common_Parameters_LinRot_Position 08 - Linear/Rotary sensors position + * @{ */ + +/** Position resolution in number of bits (range=1..8) + - A Low value will result in a low resolution and will be less subject to noise. + - A High value will result in a high resolution and will be more subject to noise. +*/ +#define TSLPRM_LINROT_RESOLUTION (7) + +/** Direction change threshold in position unit (range=0..255) + - Defines the default threshold used during the change direction process. + - A Low value will result in a faster direction change. + - A High value will result in a slower direction change. +*/ +#define TSLPRM_LINROT_DIR_CHG_POS (10) + +/** Direction change debounce (range=0..63) + - Defines the default integrator counter used during the change direction process. + - This counter is decremented when the same change in the position is detected and the direction will + change after this counter reaches zero. + - A Low value will result in a faster direction change. + - A High value will result in a slower direction change. +*/ +#define TSLPRM_LINROT_DIR_CHG_DEB (1) + +/** @} Common_Parameters_LinRot_Position */ + +//============================================================================== +// Debounce counters +//============================================================================== + +/** @defgroup Common_Parameters_Debounce 09 - Debounce counters + * @{ */ + +/** Proximity state debounce in samples unit (range=0..63) + - A Low value will result in a higher sensitivity during the Proximity detection but with less noise filtering. + - A High value will result in improving the system noise immunity but will increase the system response time. +*/ +#define TSLPRM_DEBOUNCE_PROX (3) + +/** Detect state debounce in samples unit (range=0..63) + - A Low value will result in a higher sensitivity during the detection but with less noise filtering. + - A High value will result in improving the system noise immunity but will increase the system response time. +*/ +#define TSLPRM_DEBOUNCE_DETECT (3) + +/** Release state debounce in samples unit (range=0..63) + - A Low value will result in a higher sensitivity during the end-detection but with less noise filtering. + - A High value will result in a lower sensitivity during the end-detection but with more noise filtering. +*/ +#define TSLPRM_DEBOUNCE_RELEASE (3) + +/** Re-calibration state debounce in samples unit (range=0..63) + - A Low value will result in a higher sensitivity during the recalibration but with less noise filtering. + - A High value will result in a lower sensitivity during the recalibration but with more noise filtering. +*/ +#define TSLPRM_DEBOUNCE_CALIB (3) + +/** Error state debounce in samples unit (range=0..63) + - A Low value will result in a higher sensitivity to enter in error state. + - A High value will result in a lower sensitivity to enter in error state. +*/ +#define TSLPRM_DEBOUNCE_ERROR (3) + +/** @} Common_Parameters_Debounce */ + +//============================================================================== +// Environment Change System (ECS) +//============================================================================== + +/** @defgroup Common_Parameters_ECS 10 - ECS + * @{ */ + +/** Environment Change System Slow K factor (range=0..255) + - The higher value is K, the faster is the response time. +*/ +#define TSLPRM_ECS_K_SLOW (10) + +/** Environment Change System Fast K factor (range=0..255) + - The higher value is K, the faster is the response time. +*/ +#define TSLPRM_ECS_K_FAST (20) + +/** Environment Change System delay in msec (range=0..5000) + - The ECS will be started after this delay and when all sensors are in Release state. +*/ +#define TSLPRM_ECS_DELAY (500) + +/** @} Common_Parameters_ECS */ + +//============================================================================== +// Detection Time Out (DTO) +//============================================================================== + +/** @defgroup Common_Parameters_DTO 11 - DTO + * @{ */ + +/** Detection Time Out delay in seconds (range=0..63) + - Value 0: DTO processing not compiled in the code (to gain size if not used). + - Value 1: Default time out infinite. + - Value between 2 and 63: Default time out between value n-1 and n. + - Examples: + - With a DTO equal to 2, the time out is between 1s and 2s. + - With a DTO equal to 63, the time out is between 62s and 63s. + +@note The DTO can be changed in run-time by the application only if the + default value is between 1 and 63. +*/ +#define TSLPRM_DTO (5) + +/** @} Common_Parameters_DTO */ + +//============================================================================== +// Detection Exclusion System (DXS) +//============================================================================== + +/** @defgroup Common_Parameters_DXS 12 - DXS + * @{ */ + +/** Detection Exclusion System (0=No, 1=Yes) +*/ +#define TSLPRM_USE_DXS (1) + +/** @} Common_Parameters_DXS */ + +//============================================================================== +// Miscellaneous parameters +//============================================================================== + +/** @defgroup Common_Parameters_Misc 13 - Miscellaneous + * @{ */ + +/** Timing tick frequency in Hz (range=125, 250, 500, 1000, 2000) + - Result to a timing interrupt respectively every 8ms, 4ms, 2ms, 1ms, 0.5ms +*/ +#define TSLPRM_TICK_FREQ (1000) + +/** Delay for discharging Cx and Cs capacitors (range=0..65535) + - The value corresponds to the Softdelay function parameter. + - 500 gives around 63 µs delay whatever HCLK + - 1000 gives around 126 µs delay whatever HCLK + - 2000 gives around 251 µs delay whatever HCLK +*/ +#define TSLPRM_DELAY_DISCHARGE_ALL (1000) + +/** @} Common_Parameters_Misc */ + +/** @} Common_Parameters */ + +//++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +//++++++++++++++++++++++++++++++ MCU PARAMETERS ++++++++++++++++++++++++++++++++ +//++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ + +/** @defgroup STM32F3xx_Parameters STM32F3xx Parameters + * @{ */ + +//============================================================================== +// GPIO configuration +//============================================================================== + +/** @defgroup STM32F3xx_Parameters_GPIO_Config 01 - TSC GPIOs Configuration + * @{ */ + +/** TSC GPIOs Configuration selection (range=0..1) + - 0: Manual. The TSC GPIOs configuration must be done by the application code. + - 1: Automatic. The TSLPRM_TSC_GROUPx_IOy parameters below must be filled up. + The TSC GPIOs configuration is automatically done by the STMTouch driver. +*/ +#define TSLPRM_TSC_GPIO_CONFIG (1) + +//+++ DO NOT CHANGE THESE VALUES +++++++++++++++++++++++++++++++++ +// These defines must be applied to the TSLPRM_TSC_GROUPx_IOy parameters below. +#define NU (0) // Not Used IO +#define CHANNEL (1) // Channel IO +#define SHIELD (2) // Shield IO (= Channel IO but not acquired) +#define SAMPCAP (3) // Sampling Capacitor IO +//++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ + +// If TSLPRM_TSC_GPIO_CONFIG=1 assign each TSLPRM_TSC_GROUPx_IOy parameters below. +// If TSLPRM_TSC_GPIO_CONFIG=0 these parameters are ignored. +// STM32F30X STM32F37X +#define TSLPRM_TSC_GROUP1_IO1 NU // PA0 PA0 +#define TSLPRM_TSC_GROUP1_IO2 NU // PA1 PA1 +#define TSLPRM_TSC_GROUP1_IO3 NU // PA2 PA2 +#define TSLPRM_TSC_GROUP1_IO4 NU // PA3 PA3 + +#define TSLPRM_TSC_GROUP2_IO1 NU // PA4 PA4 +#define TSLPRM_TSC_GROUP2_IO2 NU // PA5 PA5 +#define TSLPRM_TSC_GROUP2_IO3 NU // PA6 PA6 +#define TSLPRM_TSC_GROUP2_IO4 NU // PA7 PA7 + +#define TSLPRM_TSC_GROUP3_IO1 NU // PC5 PC4 << diff +#define TSLPRM_TSC_GROUP3_IO2 NU // PB0 PC5 << diff +#define TSLPRM_TSC_GROUP3_IO3 NU // PB1 PB0 << diff +#define TSLPRM_TSC_GROUP3_IO4 NU // PB2 PB1 << diff + +#define TSLPRM_TSC_GROUP4_IO1 NU // PA9 PA9 +#define TSLPRM_TSC_GROUP4_IO2 NU // PA10 PA10 +#define TSLPRM_TSC_GROUP4_IO3 NU // PA13 PA13 +#define TSLPRM_TSC_GROUP4_IO4 NU // PA14 PA14 + +#define TSLPRM_TSC_GROUP5_IO1 NU // PB3 PB3 +#define TSLPRM_TSC_GROUP5_IO2 NU // PB4 PB4 +#define TSLPRM_TSC_GROUP5_IO3 NU // PB6 PB6 +#define TSLPRM_TSC_GROUP5_IO4 NU // PB7 PB7 + +#define TSLPRM_TSC_GROUP6_IO1 NU // PB11 PB14 << diff +#define TSLPRM_TSC_GROUP6_IO2 NU // PB12 PB15 << diff +#define TSLPRM_TSC_GROUP6_IO3 NU // PB13 PD8 << diff +#define TSLPRM_TSC_GROUP6_IO4 NU // PB14 PD9 << diff + +#define TSLPRM_TSC_GROUP7_IO1 NU // PE2 PE2 +#define TSLPRM_TSC_GROUP7_IO2 NU // PE3 PE3 +#define TSLPRM_TSC_GROUP7_IO3 NU // PE4 PE4 +#define TSLPRM_TSC_GROUP7_IO4 NU // PE5 PE5 + +#define TSLPRM_TSC_GROUP8_IO1 NU // PD12 PD12 +#define TSLPRM_TSC_GROUP8_IO2 NU // PD13 PD13 +#define TSLPRM_TSC_GROUP8_IO3 NU // PD14 PD14 +#define TSLPRM_TSC_GROUP8_IO4 NU // PD15 PD15 + +/** @} STM32F3xx_Parameters_GPIO_Config */ + +//============================================================================== +// Charge Transfer Pulses +//============================================================================== + +/** @defgroup STM32F3xx_Parameters_CT_Pulses 02 - Charge Transfer Pulses + * @{ */ + +/** Charge Transfer Pulse High (range=0..15) + - 0: 1 x tPGCLK + - 1: 2 x tPGCLK + - ... + - 15: 16 x tPGCLK +*/ +#define TSLPRM_TSC_CTPH (1) + +/** Charge Transfer Pulse Low (range=0..15) + - 0: 1 x tPGCLK + - 1: 2 x tPGCLK + - ... + - 15: 16 x tPGCLK +*/ +#define TSLPRM_TSC_CTPL (1) + +/** Pulse Generator Prescaler (range=0..7) + - 0: fPGCLK = fHCLK + - 1: fPGCLK = fHCLK/2 + - ... + - 7: fPGCLK = fHCLK/128 +*/ +#define TSLPRM_TSC_PGPSC (5) + +/** @} STM32F3xx_Parameters_CT_Pulses */ + +//============================================================================== +// IOs +//============================================================================== + +/** @defgroup STM32F3xx_Parameters_IOs 03 - I/Os + * @{ */ + +/** TSC IOs default mode when no on-going acquisition (range=0..1) + - 0: Output push-pull low + - 1: Input floating +@note To ensure a correct operation in noisy environment, this parameter should +be configured to output push-pull low. +*/ +#define TSLPRM_TSC_IODEF (0) + +/** Acquisition Mode (range=0..1) + - 0: Normal acquisition mode + - 1: Synchronized acquisition mode +*/ +#define TSLPRM_TSC_AM (0) + +/** Synchronization Pin (range=0..2) + - 0: PB08 + - 1: PB10 + - 2: PA15 (on some devices only) +*/ +#define TSLPRM_TSC_SYNC_PIN (0) + +/** Synchronization Polarity (range=0..1) + - 0: Falling edge only + - 1: Rising edge and high level +*/ +#define TSLPRM_TSC_SYNC_POL (0) + +/** @} STM32F3xx_Parameters_Misc */ + +//============================================================================== +// Spread Spectrum +//============================================================================== + +/** @defgroup STM32F3xx_Parameters_SpreadSpectrum 04 - Spread Spectrum + * @{ */ + +/** Use Spread Spectrum (0=No, 1=Yes) +*/ +#define TSLPRM_TSC_USE_SS (0) + +/** Spread Spectrum Deviation (range=0..127) + - 0: 1 x tSSCLK + - 1: 2 x tSSCLK + - ... + - 127: 128 x tSSCLK +*/ +#define TSLPRM_TSC_SSD (0) + +/** Spread Spectrum Prescaler (range=0..1) + - 0: fSSCLK = fHCLK + - 1: fSSCLK = fHCLK/2 +*/ +#define TSLPRM_TSC_SSPSC (0) + +/** @} STM32F3xx_Parameters_SpreadSpectrum */ + +/** @} STM32F3xx_Parameters */ + +// DO NOT REMOVE !!! +#include "tsl_check_config.h" + +#endif /* __TSL_CONF_STM32F3XX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |